Orion Car Audio HCCA 275G4 2-Channel Car Amp
Out of stock |
Similar in Car Amplifiers
- Amplifier Type: Dual Channels
- RMS Power at 4 Ohms: 75 W x 2
- Number Of Channels: 2
- 3 Way Ready: No
- Bridgable: Bridgable
- RMS Power at 2 Ohms: 150 W x 2
- Overview
-
Reviews
-
Compare Prices
User ReviewRead All Reviews »
the last amp ill ever buy
Pros
underrated, eye turner, clean power, low ohm loads, made in the usa, big, cheap.
Cons
class a/b amp requires lotsOFpower, cost of powerWire and accessories just to run it sucks.
Recommended it?
Yes
The Bottom Line:
ONE WORD ORION!!! old school at least
I have had this amp since 2000. i have NEVER had any problems with it. it is very underrated and puts out very clean power if you have the electrical system to keep up with its demands. the specs for this amp are awesome.
75x2 4ohms 300x1 4ohms
150x2 2ohms 600x1 2ohms
300x2 1ohm 1200x1 1ohm
600x2 .5ohms
all ratings are at 12 volts!!! i am putting 14.5-14.9 volts back to this monster. so i am probably seeing more like 1600-1700 watts at 1 ohm mono. i am powering 3 jl10wo's right now at 4 ohms mono. i would have to say that i am getting at least 400 watts at 4 ohms due to the increased voltage. these subs are pounding, i have 3 more i am going to put in to drop the ohm load down to 2 ohms mono. i should be putting the 125rms into each one. i cant wait. now i have had this amp down to a 1 ohm load and let me tell you that i saw2 to 3 volt drops from its massave 180amp fuze rating. i try to keep her at 2 ohms or abve, my electrical system handles that load fine. its an awesome amp, i havent had one problem with it ever. if you can get your hands on one, make sure you run at lease 1/0 gauge into a distribution block to feed it its dual 4 gauge power requirements. get a cap or two and upgrade your alternator. my 6 10's are going to sound awesome, and just think, they are 12 ohm subs, i could run 12 of them to get a one ohm load and i still would have rms going into each one :) later
75x2 4ohms 300x1 4ohms
150x2 2ohms 600x1 2ohms
300x2 1ohm 1200x1 1ohm
600x2 .5ohms
all ratings are at 12 volts!!! i am putting 14.5-14.9 volts back to this monster. so i am probably seeing more like 1600-1700 watts at 1 ohm mono. i am powering 3 jl10wo's right now at 4 ohms mono. i would have to say that i am getting at least 400 watts at 4 ohms due to the increased voltage. these subs are pounding, i have 3 more i am going to put in to drop the ohm load down to 2 ohms mono. i should be putting the 125rms into each one. i cant wait. now i have had this amp down to a 1 ohm load and let me tell you that i saw2 to 3 volt drops from its massave 180amp fuze rating. i try to keep her at 2 ohms or abve, my electrical system handles that load fine. its an awesome amp, i havent had one problem with it ever. if you can get your hands on one, make sure you run at lease 1/0 gauge into a distribution block to feed it its dual 4 gauge power requirements. get a cap or two and upgrade your alternator. my 6 10's are going to sound awesome, and just think, they are 12 ohm subs, i could run 12 of them to get a one ohm load and i still would have rms going into each one :) later
