MODEL 50HERKRC Motion Detector Remote Control Motion Detector Remote control for the LiftMaster® motion detector to conveniently choose from 8 different preset comfort functions, to adjust detection fields, mounting heights, relay hold interval, cross traffic optimization, direction recognition, people/vehicle separation, slow motion detection, turn on/off filter functions, open the door manually and much more. Bidirectional Fine-tune the motion detector from the ground without guessing if all the settings have been received by the sensor

New Page 2 Remote DTMF Controllers - Controls Door Strikes and Gate Openers From a Touch Tone Phone. Designed for use with W-1000/2000/3000 Doorboxes or as a stand-alone 'Dial-up' remote Touch Tone controller. This unit can operate door strikes, gate openers, or control equipment at remote locations (the RC-2A and RC-3 can answer a ringing line) using a Touch Tone phone. The RC-2A can activate 1 momentary or maintained relay closure while the RC-3 can provide 3 relay contacts. Three RC-3s can be connected to the same line for 9 outputs. Tones confirm relay action. Either unit can be set up to operate with or without security codes. The RC-3 has a built-in pulse dialer activated by an external alarm contact. The RC-3 will dial a number up to three times, sending alert tones. (Power supply... Less

Control Panel, Transformer, Keypad, Battery, Speaker and RJ31X - The newest member of the ELK M1 Control Family, offers an economical solution for installations not requiring the voice and telephone remote control capability of the M1 Gold. Unlike controls that only offer basic security capability, M1EZ8 is a powerful, rock solid security control with the most imaginative automation functionality available. Built on the same software architecture as the M1 Gold, the possibilities for expansion, networking, and option for programming and control over the internet make the M1EZ8 an exceptional value. Installers will value the flash memory firmware, fast PC programming, ease of installation, plus optional RS-232 serial port and Ethernet connectivity. End users will... Less

Kohler OnCue Generator Remote Management System Software OnCue Generator Management System Software has updated features for the NEW RDC2/RDC controllers on the Kohler 14RESA/RESAL and 20RESA/RESAL models. Features: Allows homeowners to remotely manage generator performance from anywhere in the world Relays status messages to you or your local Kohler dealer View real-time status of generator operation Observe and/or clear any diagnostic fault codes Review a time-stamped history of faults and clearing of faults View multiple gensets on one screen Additional Features When Used with the Kohler Load Control Module (LCM)* View current loads and shed loads Dual color LEDs for each load indicate load status (powered or shed) and flash to indicate a test Even More Additional... Less

The CC12 is an IR remote controlled double pole/double throw relay module. It provides dry contact closures to satisfy a variety of uses, such as activation of screen drops, and projector lifts. The switching is accomplished by way of infrared commands originating from a Xantech RC68+ programmer (or RC68 programmer). It can also be switched by a DC voltage applied between the CI (control input) and GND terminals. The RC68+ commands are "taught" to learning devices and passed to the IR IN, and GND input terminals of the CC12 signal input terminals via Xantech IR receivers, keypads and connecting blocks.

The MINIPORT-20 Power Relay is a NRTL-C TUV listed, 20 amp, relay switched 120 VAC outlet, with a terminal strip that allows remote control via safe, inexpensive, low voltage Class 2 wiring. It includes an internal 12 VDC supply, and can be controlled from a remote location with maintained or momentary contact switches. Multiple MINIPORTs may be connected together so that all are controlled by a single switch closure, and may be linked so that all turn on simultaneously or one by one, in a delayed sequence. If delayed, the delay interval between the turn-on of one MINIPORT and the next is approximately 3 seconds. (Delayed turn-on is useful in avoiding large inrush currents that can trip house circuit breakers, that would otherwise occur if all amps were turned on simultaneously.)... Less

The KTD-135 is a small indoor receiver that controls access through a door. It is designed for use in a Digiplex® system. The unit receiver contains one dry contact relay and a built-in tone generator for remote site call-in annunciation. FEATURES: 1-amp dry contact relays Call-in capability for site annunciation Audio follow relay for connection to audio bus Small, easy-to-mount case Powered from 9 VAC transformer PDF Spec Sheet

The Fire-Lite MS-5UD five zone, and MS-10UD ten zone Fire Alarm Control Panels bring the latest in technology to conventional fire controls. The MS-5UD and MS-10UD are fully programmable via built-in keypad and 80 character LCD display, so you do not need an external programmer. Both panels have a built-in Digital Alarm Communicator Transmitter (DACT) and availability to add optional equipment: Remote annunciator, Relay module, LED Driver module, Transmitter module and Printer interface module. Both panels are compatible with the new i3 smoke detectors from System Sensor, providing such advanced features as drift compensation, maintenance alert, and freeze warning features normally found in more expensive addressable systems. The Notification Appliance Circuit (NAC) protocol includes the... Less

RS60 6v OUT 6V DC compact Remote Control Switcher -Best gadget ever!-Remotely turn On and Off for any 6 Volt DC devices such as computer lighting accessories, auto lighting kits, landscaping lighting, boat lighting or other electronic applications.-Comp act size and mounting holes make it easier for installation.-Kit includes one receiver box and 2 remote controls. Specs: Input/output voltage: DC 6V in, DC 6V out Remote: steady range ~50ft, on/off button, Range can be extending further depend in

When you want it all…the ThermaSol wireless, infrared, in-shower SRT Remote Control is designed to utilize all the features of the selected ThermaSol control from the comfort of your steam/shower seat. Designed for use with the Serenity Light and Music System, your control selections can be audibly confirmed by ThermaSol’s “Virtual Spa Attendant” or Voice Response system. This ergonomic hand-held remote fits in your palm, is completely waterproof and offers the ultimate in ThermaSol steambathing control. Wall-mount remote holder included and requires use of the SLST and an SET-NTS or TPT-NTS control package. Features include: Infrared, wireless remote control; Activates all SET and TPT control features; Ergonomic, easy to operate and fits in your palm; Inside the steam/shower operation;... Less

This is a 12VDC On/Off remote control device. It is shock resistant with a special design to eliminate the click sound generated by relay contact. Its compact structure makes the installation possible in most space-constraint applications. Typical applications includes but not limited to vehicle anti-theft device, computer modding, automobile lighting, home decoration lighting, security systems, landscaping irrigation or sprinkler control and much more... Specifications: Operating Voltage: DC 12+/- 10% Operatong Current: 3Amp Output Power: 36W Operating Range: 30Meter

The SR21 is an IR remote controlled A/B speaker relay module. It allows the installer and user to switch the output of one stereo amplifier between two speaker pairs, or, to switch one speaker pair between the outputs of two stereo amplifiers. The switching is accomplished by way of infrared commands originating from a Xantech RC68+ (or RC68) programmer. It can also be switched by a DC voltage applied between the CI (control input) and GND terminals. The RC68+ commands are "taught" to learning devices and passed to the IR IN and GND input terminals of the SR21 via Xantech IR receivers, keypads and connecting blocks.

The unique circuitry of the 750 Series II Conductivity Monitor/controlle rsguarantee accurate and reliable measurements. Drift free performance is assured by "field proven" electronics, including automatic DC offset compensation and highly accurate drive voltage.Since temperature compensation is at the "heart" of accurate water measurement, all Myron L Monitor / controllers feature a highly refined and precise TC circuit. This feature perfectly matches the water temperature coefficient as it changes. All models corrected to 25°C. Uncompensated models available to conform with USP 25. A push-to-test button makes setpoint checks easy, while the internal alarm set discourages unauthorized adjustments. Standard on all controller models is a heavy-duty 10 amp output relay, operating on either... Less

The Fire-Lite MS-5UD five zone, and MS-10UD ten zone Fire Alarm Control Panels bring the latest in technology to conventional fire controls. The MS-5UD and MS-10UD are fully programmable via built-in keypad and 80 character LCD display, so you do not need an external programmer. Both panels have a built-in Digital Alarm Communicator Transmitter (DACT) and availability to add optional equipment: Remote annunciator, Relay module, LED Driver module, Transmitter module and Printer interface module. Both panels are compatible with the new i3 smoke detectors from System Sensor, providing such advanced features as drift compensation, maintenance alert, and freeze warning features normally found in more expensive addressable systems. The Notification Appliance Circuit (NAC) protocol includes the... Less

RM104, universal 4 channels key less relay switches Switch up to 4 different devices, included 4 receivers, separately.With our RM104 kit, you can control up to 4 different devices in 4 different locations, and control with just one remote control transmitter.We also included an extra remote for spare as shown in picture.With this RM104, you can turn On and Off any 12 Volt DC devices such as auto lighting kits, computer accessories and other electronic applications, it is easy to wire with basi

~ 433MHz Dip-Switch Receiver ~ 2-Relay Output ~ Use with any 433MHz dip-switch transmitters ~ 1.5mA Low Consumption

The Aqua Logic System has 4 different control options available. 1. Wall Mounted Wired Remote - The wired remote requires 4 conductor wire to be run from the equipment pad to the location in the house where the Wall Mounted Wired Remote will be hooked to the wall. You can Add Up to 3 Wired Remotes to your Aqua Logic system. If you are adding the Aqua Logic to an existing pool, the wireless remote may be a better option. 2. Wall Mounted Wireless Remote - Aqua Logic wireless remotes require a Wireless Base Receiver. Only 1 Base Receiver is needed to operate any combination of 4 wireless remotes. The Wall Mounted Wireless Remote does not require any connections from the remote to the equipment set. This makes the wireless option ideal for retrofit applications. Unlike table top wireless... Less

4-Channel AVD-4040 RC Circuits and Arm/Disarm. Features: Remote Arming or Disarming of Dialer system and control channels - Entry/Exit alarm control from any phone, anywhere. 4 external circuits can be Remotely Con-trolled (closed or opened) using the but-tons on any cell or landline phone. A circuit's status (open or closed) can be verified with phone keypad commands and audible tone responses. Shut out Sensors and False Alarms. 4 Separate voice message alarm zones. Calls up to 8 telephone or cell phone numbers. Remote Turn Off feature allows termination of activated channel. Built-In Line Seizure. Listen-In verification and communication. Built-In Auxiliary Output to drive external. Siren, strobe or relay. EEPROM Memory retains programming despite power loss.

RP800 Universal Remote Control Simple open/close Switch with 0v output contact with 500ft control range O volt output: this kit will not supply any voltage/power to output device, it only act as an open or close contact switch to connecting device. Need an output switch that can be controlled remotely? want to control your toy far far away? 500ft away? Here is the gadget just made for that purpose, use this kit as a simple switch to make contact open or close remotely up to 500ft away. can go e

This is a 2-zone (2-Channel)12VDC ON and OFF relay controlled by one keychain style handheld transmitter. There are 2 sets of ON and OFF keys, total 4keys to individually control the two zones. The keychain style transmitter was made with a solid metal frame and a sliding protection cover to avoid the accidental press of the keys. Includes: 2 control boxes and 1 remote control. Turn lights, LED, anything low power on/off remotely in two different area's. Features This is a 2 zone receiver with 1 transmitter. The 2-zone outputs are controlled by two sets of keys on the transmitter with On and Off function. Here is the key function and output chart: Left Output Zone 1 Reception, left upper key ON, left lower key OFF. Right Output Zone 2 Reception, right upper key ON, right lower key OFF ... Less

~ 433MHz Dip-Switch Receiver ~ 2-Relay Output, 12/24V ac/dc ~ Use with any 433MHz dip-switch transmitters

Advanced technology The Polaris Eos promises improvements in technology ahead of its time with 5GHz frequency. The high-speed communication band extends range and quality of transmission for immediate powering up. Real home automation The Polaris Eos creates real home automation with easy controls for the pool, spa, and water features from the equipment area or from inside the home. With an optional Power Line Carrier (PLC) kit, the Polaris Eos acts as a transmitter and through X-10 receiver modules operates up to 256 electric devices including stereos and lighting. Modular system components Sophisticated modular components allow the homeowner to personalize their system to specific needs. Designed for total automation, the Polaris Eos has built-in expandability that allows options to be... Less

RS90: Universal 9V DC remote control switch kit For remotely turn on and off small 9V DC application uses in automobile, motorcycle, boat, RV, boat, home, garden, hunting tool and any 9V device receiver comes with wires for easy installation. Specs:Kit included: 1 switch receiver box, remote transmitter (batteries included) Dimension: remote 2"x 1 3/8" , receiver box 2 1/8" x 1 7/8"Remote mode: on and off, toggle mode Remote range: ~60ft/~20m (Remote range and signal strength depend on where dev

The Samsung SNS-110 is a simple solution to remote video surveillance over the Internet or Intranet. This high speed remote video system allows the user to monitor thier office/house at a faster speed of frames. This system comes with everything you need to monitor your location, simply put together for do it yourself installation. You can connect up to four black and white or color cameras. The cameras can be viewed remotely in quad or sequential switching screen. The administrator can control the right of the users by using unique ID and password. User access can be restricted by using password. WELDEX WDB5407S- Color bullet camera indoor, outdoor with mounting bracket. 4.3 wide-angle lens. Clear true to life picture, 400 lines of resolution. Minimum illumination 1 lux works great in... Less

Remote Relay Module, Depth 1 1/2 In, Height 3 3/8 In, Width 2 3/4 In, Ambient Temp Limits 32 To 120 F, For Use With 1exw9, 1exy1, 1exy2

The unique circuitry of the 750 Series II Conductivity Monitor/controlle rsguarantee accurate and reliable measurements. Drift free performance is assured by "field proven" electronics, including automatic DC offset compensation and highly accurate drive voltage.Since temperature compensation is at the "heart" of accurate water measurement, all Myron L Monitor / controllers feature a highly refined and precise TC circuit. This feature perfectly matches the water temperature coefficient as it changes. All models corrected to 25°C. Uncompensated models available to conform with USP 25. A push-to-test button makes setpoint checks easy, while the internal alarm set discourages unauthorized adjustments. Standard on all controller models is a heavy-duty 10 amp output relay, operating on either... Less

The WE-318 comes with (1) TM-318 Transmitter and (1) WE-001 Wall Switch. The Wall Switch simply replaces your existing wall switch and can control your lamp or light fixture- including turning it ON, OFF or Dimming-by simply touching its surface. The Transmitter functions as a remote to manipulate the switch remotely from as far as 300 feet away, so even larger rooms or spaces can accommodate the WE-318's functionality. Conveniently, the remote transmitter can SNAP ON to the Wall Switch itself, whereby you can control the unit and ensure it won't be lost while not in use.

Broncolor RFS 2 Transmitter slides into the hot shoe of the camera. The flash is synchronized either via the central contact of the hot shoe or via a short cable to the camera. The miniature transmitter has 99 studio addresses for selective and wireless flash triggering, as well as a "test" button for direct triggering.The operating status of the transmitter, the studio address and the frequency channel are indicated on the large LCD display. Two additional buttons allow remote regulation of the power of all the controlled flash units directly from the transmitter. Outdoors or in large halls, the operating distance of the broncolor RFS 2 is up to 200 m, in closed rooms up to 50 m. The delay time is less than 400 microseconds.

•2 year limited warranty • Operate gate or garage with compatible 433 MHz receiver • Operates up to 300 ft typically Transmitter Setup: (It is recommended that the dipswitch code be changed from the default factory setting) 1. Open the battery compartment door and locate the dipswitches. 2. Change the dipswitches to the settings you prefer, record for future reference Transmitter Left Button to Receiver Programming: (standard Open/Stop/Close function) Press and hold the left transmitter button down. Red light on transmitter should be on. On the receiver, push the P1 push-button until the green LD light comes on. Release both buttons. Transmitter left button to receiver programming is complete. Transmitter Right Button to Receiver Programming: (Hold-Gate-Open) (Only if auto... Less

This receiver, which includes a 9.8 foot long cable, plugs into the jack on the rear of the projector and disables the projector's IR receiver. It allows projector configuration where the remote control has no line of site path and will also work with the projector in a separate room for rear projection. Also, this kit includes option to hardwire the remote to the projector.